Sample preparation on ceramics composite for cutting tools in high speed machining

Sample preparation on ceramics composite for cutting tools in high speed machining

Bibliographic Details
Main Authors:	Sutjipto, Agus Geter Edy, Kaderi, Akbar
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/18108/ http://irep.iium.edu.my/18108/ http://irep.iium.edu.my/18108/1/5.pdf

Similar Items

Coating for high speed cutting tools
by: -, Suryanto
Published: (2011)

Development of ceramics cutting tool for machining using aluminium oxide reinforced with copper powder
by: Muhammad Aiman, Ishak
Published: (2016)

Cutting force impact to tool life of CT5015 in high speed machining by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2012)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Cutting tool angle of lathe machine for different materials
by: Normawati, Mansor
Published: (2008)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

Effects of Irregular Tool Geometry and Machining Process Parameters on the Wavelength Performance of Process Damping in Machining Titanium Alloy at Low Cutting Speed
by: Muhammad Adib , Shaharun, et al.
Published: (2015)

Experimental investigation of chip tool contact process and determination of optimum cutting speed for steel of any composition
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Effect of High-Speed Milling Tool Path Strategies on the Surface Roughness of Stavax ESR Mold Insert Machining
by: Mebrahitom, A., et al.
Published: (2016)

Influence of work material, cutting conditions and rigidity of tool holders on machine tool chatter
by: Amin, A. K. M. Nurul
Published: (1992)

Development of new model for cutting force in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Effects of tool path strategies on surface roughness in high speed milling
by: Abdul Rashid, Muhammad
Published: (2012)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Effect of Dry Cutting on Force and Tool Life when Machining Aerospace Material
by: K., Kadirgama, et al.
Published: (2010)

Experimental investigations in high-speed hard turning of AISI 4340 steel using mixed ceramic
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of tooling cost model in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Suppression of Chatter in High Speed Milling Machine Using Spindle Speed Variation Method with Acoustic Feedback PID Controller
by: Suparmaniam, Madan Varmma, et al.
Published: (2019)

The effect of CaO addition on the microstructural, mechanical and dielectric properties of pure MgO ceramic
by: Sutjipto, Agus Geter Edy
Published: (2007)

Enhancing tool life with the development of silicon nitride based inserts for high speed machining of Inconel 718 using hybrid microwave sintering
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

Multi-response optimizations for high speed ductile mode machining of soda lime glass
by: Bagum, Nasima, et al.
Published: (2015)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Advanced machining towards improved machinability of difficult-to-cut materials
Published: (2011)

Microstructural and process characterization on the electrical conductivity and electrical discharge machinability of Al2O3-based ceramic composites
by: Mebrahitom, A., et al.
Published: (2018)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

The strength of SiO2 added MgO ceramics to withstand flashover-treeing appearance under electron bombardment in vacuum
by: Sutjipto, Agus Geter Edy
Published: (2004)

Study on Optimal Surface Property Of WC-Co Cutting Tool for Aluminium Alloy Cutting
by: Mohd, Nizar, et al.
Published: (2016)

High precision estimation on physical behavior for cutting with various tool rake angle by finite element method
by: Ahmad Shahir, Jamaludin, et al.
Published: (2018)

Elimination of burr formation during end milling of Polymethyl Methacrylate (PMMA) through high speed machining
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Spindle speed modulation for chatter suppression in machining process
by: Amirul Hakim, Kamarazaman
Published: (2016)

Study on metal removing from alumina ceramics
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

Tool life estimation model based on simulated flank wear during high speed hard turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

The effect of varying cutting speeds on tool wear during conventional and Ultrasonic Assisted Drilling (UAD) of Carbon Fibre Composite (CFC) and titanium alloy stacks
by: Dahnel, Aishah Najiah, et al.
Published: (2016)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

A new experimental approach to determination of critical depth in high speed machining of soda-lime glass
by: Mahmud, M.A, et al.
Published: (2012)

Investigation of burr in high speed microdrilling
by: Ali, Mohammad Yeakub, et al.
Published: (2013)