Design and fabrication of industrial welding robotic arm

Design and fabrication of industrial welding robotic arm

Bibliographic Details
Main Authors:	Syed Abdullah, Syed Idros, Mahamad Puzi, Mohamad Syatbi, Wan Yusoff, Wan Ahmad Yusmawiza
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TA401 Materials of engineering and construction
Online Access:	http://irep.iium.edu.my/21338/ http://irep.iium.edu.my/21338/ http://irep.iium.edu.my/21338/1/7.pdf

Similar Items

Implementation of FMECA on Fixed Assembly Cell (FAC)
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Resistive switching of Cu/Cu2O junction fabricated using simple thermal oxidation at 423 K for memristor application
by: Ani, Mohd Hanafi, et al.
Published: (2018)

Reverse engineering for rapid prototyping of automotive components
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Performance measurement of SMEs manufacturing sector in Malaysia
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

The introduction of fit manufacturing as a performance measuring approach towards sustainability of selected manufacturing companies in Malaysia
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Fabrication of nickel aluminide intermetallic-alumina nanocomposite
by: Ismail, Roslina, et al.
Published: (2011)

Micro connector fabricated by micro process technology
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2000)

A surgical training model manufacture using fused deposition modeling
by: Mohamad Ali, Hasanudin Hafis, et al.
Published: (2011)

Effect of voltage on the consolidation of TiC particulates on steel substrate fused by TIG welding ARC
by: Mridha, Shahjahan, et al.
Published: (2012)

Influence of water molar ratio on fabrication of silica ceramic membranes via sol-gel dip-coating method
by: Kahlib, Nor Amyra Zulianey, et al.
Published: (2018)

Fabrication of CuSiC composite by powder metallurgy route
by: A. R. , Fatimah Azreen, et al.
Published: (2011)

Fabrication and characterization of poly (ethylene oxide) for photo-electronic devices
by: Alaei, Iraj, et al.
Published: (2015)

Protein foaming-consolidation method for fabrication of high performance porous bioceramics
by: Sopyan, Iis, et al.
Published: (2013)

Fabrication of metal matrix composite automotive brake rotor: part 1
by: Maleque, Md. Abdul
Published: (2011)

Fabrication of metal matrix composite automotive brake rotor: part 2
by: Maleque, Md. Abdul
Published: (2011)

Fabrication and sintering behavior of zinc-doped biphasic calcium phosphate bioceramics
by: Sopyan, Iis, et al.
Published: (2016)

Fabrication of nickel aluminide (Ni3Al) by hot isostatic pressing (HIP)
by: Abu Zarim, Faizal, et al.
Published: (2011)

Micro connector for high packaging density fabricated by using UV Thick Photoresist
by: Unno, Toshinori, et al.
Published: (2002)

Fabrication of biodegradable composite – an implication of plasticizer
by: Kaiser, Mohammad Rejaul, et al.
Published: (2010)

The study of the implementation of OHSAS: 18001 at Kulliyyah of Engineering
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Chemical resistance tests on PP-ternary nanocomposite for its application in bioreactor liner fabrication
by: Yusof, Faridah, et al.
Published: (2011)

Variation of fiber architecture on loads applied in fabrication of epoxy/woven fiber glass composites
by: Md Idriss, Ahmed Nazrin, et al.
Published: (2011)

Application of low cost polyurethane (PU) foam for fabricating porous tri-calcium phosphate (TCP)
by: Abdul Rahman, Fariza, et al.
Published: (2010)

Fabrication of flexible Au/ZnO/ITO/PET memristor using dilute electrodeposition method
by: Fauzi, Fatin Bazilah, et al.
Published: (2015)

Improvement of typical hip-joint design for gripping and fixing
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

Design for manufacture: towards improved manufacturability
Published: (2011)

Design of bicycle helmet using FEA
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Top-down fabrication of single crystal silicon nanowire using optical lithography
by: Za'bah, Nor Farahidah, et al.
Published: (2012)

Fabrication and characterization of CNT/ZnO thin film junction for photovoltaic application
by: Al-Bat’hi, Souad A. M., et al.
Published: (2019)

Design of a simple and affordable electric bicycle
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Mould design for handphone casing using moldflow
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Design and performance analysis of VCO for standard GSM using MEMS
by: Al-Khateeb, Khalid A. Saeed, et al.
Published: (2010)

Carbon dioxide capture at various temperatures using Ca(OH)2 sorbent fabricated by sol-gel route in ethanol media
by: Mohd Daud, Farah Diana, et al.
Published: (2014)

Mechanochemical synthesis of sodium doped hydroxyapatite powder
by: Syed Abu Bakar, Sharifah Adzila, et al.
Published: (2013)

Effect of titania and magnesia on the physical properties of zirconia toughened alumina
by: Manshor, Hanisah, et al.
Published: (2016)

Thermal, structural and mechanical properties of melt drawn curloaded poly(lactic acid) fibers
by: Syed Shaharuddin, Sharifah Imihezri, et al.
Published: (2017)

Miscibility, mechanical, and thermal properties of polylactic acid/polypropylene carbonate (PLA/PPC) blends prepared by melt-mixing method
by: Haneef, I.N.H.M., et al.
Published: (2018)

Effect of dipping number on the fabricated silica ceramic membranes via sol dip-coating method
by: Kahlib, Nor Amyra Zulianey, et al.
Published: (2017)

Materials selection and design
by: Maleque, Md. Abdul, et al.
Published: (2013)

Dependence of the fracture toughness on the sintering time of dense hydroxyapatite bioceramics
by: Tolouei, Ranna, et al.
Published: (2011)