Micro electro discharge machining of micro pillar array: process development

Micro electro discharge machining of micro pillar array: process development

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, -, Wan Emira Azaty, -, Nor Suriza
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/25867/ http://irep.iium.edu.my/25867/ http://irep.iium.edu.my/25867/1/Chapter_25.pdf

Similar Items

Micro electro discharge machining of micro pillar array: analysis of surface finish
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Micro electro discharge machining of micropillar array: analysis of material removal rate
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Fabrication of micro filter by electro discharge machining
by: -, Abdus Sabur, et al.
Published: (2011)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Micro electro discharge machining of nonconductive ceramic: the issue of spalling
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Influence of nano powder mixed dielectric fluid on surface finish in micro electro discharge machining of zirconia
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Effects of flushing on electro-discharge machined surface
by: Shamsul Shahril, Mat Yunus
Published: (2008)

Dimensional accuracy in dry micro wire electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Present and future research trend in electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Dry electrical discharge machining: an environmental friendly machining process
by: Ali, Mohammad Yeakub
Published: (2018)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Investigation of machining parameters for the multiple-response optimization of micro electrodischarge milling
by: Mehfuz, Reyad, et al.
Published: (2009)

Numerical Simulation of Multiple Arrays Arrangement of Micro Hydro Power Turbines
by: At-Tasneem, Mohd Amin, et al.
Published: (2014)

Experimental determination of convective heat transfer coefficient in wire electro discharge machining
by: Nadiah Waznah, Zabidi
Published: (2008)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Cfd simulation of multiple array arrangement of micro hydro power turbines
by: Thiwaan Rao, Narasimma Naidu
Published: (2013)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Micro-drilling of metallic materials for microsystems technology
by: Ali, Mohammad Yeakub
Published: (2008)

Geometrical integrity of microholes produced by micro-EDM
by: Ali, Mohammad Yeakub
Published: (2008)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Mass-replication of micro-components
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Micro end milling of AISI 304 stainless steel and analysis of micro surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Micro-electro discharge machining of nonconductive zirconia ceramic: investigation of MRR and recast layer hardness
by: Banu, Asfana, et al.
Published: (2014)

Vibration issue in micro end milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Enhancing μ-wedming (wire electro-discharge machining) of polished silicon wafer by conductive coating
by: Rasheed, Aous Naji, et al.
Published: (2014)

Optimization of Electro Discharge Machining Parameters for Drilling Titanium in Small Holes Using Taguchi Method
by: Hazami, Che Hussain, et al.
Published: (2014)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

Cannot write session to /tmp/vufind_sessions/sess_ti5iadqpl1i1t8s8bs16t5guf3