Multi objective optimisation for high speed end milling using simulated annealing algorithm
Machining at high cutting speeds produces higher temperatures in the cutting zone. These temperatures affect the surface quality and flank wear progress. Therefore, determining the optimum cutting levels to achieve the minimum surface roughness and flank wear is an important for it is economical an...
| Main Authors: | , , , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Trans Tech Publications, Switzerland
2015
|
| Subjects: | |
| Online Access: | http://irep.iium.edu.my/42928/ http://irep.iium.edu.my/42928/ http://irep.iium.edu.my/42928/1/AMR.1115.113.pdf |
| id |
iium-42928 |
|---|---|
| recordtype |
eprints |
| spelling |
iium-429282015-05-19T03:46:01Z http://irep.iium.edu.my/42928/ Multi objective optimisation for high speed end milling using simulated annealing algorithm Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas Shaffiar, Norhashimah Seder, Amin M. F. Riza, Muhammad T Technology (General) Machining at high cutting speeds produces higher temperatures in the cutting zone. These temperatures affect the surface quality and flank wear progress. Therefore, determining the optimum cutting levels to achieve the minimum surface roughness and flank wear is an important for it is economical and mechanical issues. This paper presents the optimization of machining parameters in end milling processes by using the simulated annealing algorithm (SAA) as one of the unconventional methods in optimization. The minimum arithmetic mean roughness (Ra) and minimum flank wear length were the objectives. The mathematical models have been developed, in terms of cutting speed, feed rate, and axial depth of cut by using Response surface Methodology (RSM). This paper presents the optimum cutting parameters: cutting speed, feed rate and depth of cut to achieve the minimum values of surface roughness and minimum flank wear length. The results show that the cutting speed in the range of 200 m/min, feed rate of 0.05 mm/tooth and depth of cut of 0.1mm gave the minimum arithmetic mean roughness (Ra) for 164 and minimum flank wear for 0.0379 in the boundary design of the experiment after 8000 iteration. Trans Tech Publications, Switzerland 2015 Article PeerReviewed application/pdf en http://irep.iium.edu.my/42928/1/AMR.1115.113.pdf Al Hazza, Muataz Hazza Faizi and Adesta, Erry Yulian Triblas and Shaffiar, Norhashimah and Seder, Amin M. F. and Riza, Muhammad (2015) Multi objective optimisation for high speed end milling using simulated annealing algorithm. Advanced Materials Research, 1115. pp. 113-116. ISSN 1022-6680 http://10.4028/www.scientific.net/AMR.1115.113 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
International Islamic University Malaysia |
| building |
IIUM Repository |
| collection |
Online Access |
| language |
English |
| topic |
T Technology (General) |
| spellingShingle |
T Technology (General) Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas Shaffiar, Norhashimah Seder, Amin M. F. Riza, Muhammad Multi objective optimisation for high speed end milling using simulated annealing algorithm |
| description |
Machining at high cutting speeds produces higher temperatures in the cutting zone. These temperatures affect the surface quality and flank wear progress. Therefore, determining the optimum cutting levels to achieve the minimum surface roughness and flank wear is an important
for it is economical and mechanical issues. This paper presents the optimization of machining parameters in end milling processes by using the simulated annealing algorithm (SAA) as one of the unconventional methods in optimization. The minimum arithmetic mean roughness (Ra) and
minimum flank wear length were the objectives. The mathematical models have been developed, in terms of cutting speed, feed rate, and axial depth of cut by using Response surface Methodology (RSM). This paper presents the optimum cutting parameters: cutting speed, feed rate and depth of cut to achieve the minimum values of surface roughness and minimum flank wear length. The results show that the cutting speed in the range of 200 m/min, feed rate of 0.05 mm/tooth and depth of cut of 0.1mm gave the minimum arithmetic mean roughness (Ra) for 164 and minimum flank wear for 0.0379 in the boundary design of the experiment after 8000 iteration.
|
| format |
Article |
| author |
Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas Shaffiar, Norhashimah Seder, Amin M. F. Riza, Muhammad |
| author_facet |
Al Hazza, Muataz Hazza Faizi Adesta, Erry Yulian Triblas Shaffiar, Norhashimah Seder, Amin M. F. Riza, Muhammad |
| author_sort |
Al Hazza, Muataz Hazza Faizi |
| title |
Multi objective optimisation for high speed end milling using simulated annealing algorithm |
| title_short |
Multi objective optimisation for high speed end milling using simulated annealing algorithm |
| title_full |
Multi objective optimisation for high speed end milling using simulated annealing algorithm |
| title_fullStr |
Multi objective optimisation for high speed end milling using simulated annealing algorithm |
| title_full_unstemmed |
Multi objective optimisation for high speed end milling using simulated annealing algorithm |
| title_sort |
multi objective optimisation for high speed end milling using simulated annealing algorithm |
| publisher |
Trans Tech Publications, Switzerland |
| publishDate |
2015 |
| url |
http://irep.iium.edu.my/42928/ http://irep.iium.edu.my/42928/ http://irep.iium.edu.my/42928/1/AMR.1115.113.pdf |
| first_indexed |
2023-09-18T21:01:10Z |
| last_indexed |
2023-09-18T21:01:10Z |
| _version_ |
1777410632905129984 |