Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan

The mechanical and physical propertics of titanium foam sintered at different temperatures are reported in this paper. In this work, the slurry method has been used for the production of titanium foams using pure titanium and titanium alloy (Ti6Al4V). The titanium slurry was first prepared by mixing...

Full description

Bibliographic Details
Main Authors:	S. Ahmad, N. Muhammad, A. Muchtar, J. Sahari, K.R Jamaludin, M.H.I. Ibrahim, N. H. Mohamad Nor, Murtadhahadi
Format:	Article
Language:	English
Published:	Universiti Kebangsaan Malaysia 2010
Online Access:	http://journalarticle.ukm.my/328/ http://journalarticle.ukm.my/328/ http://journalarticle.ukm.my/328/1/

id	ukm-328
recordtype	eprints
spelling	ukm-3282016-12-14T06:27:04Z http://journalarticle.ukm.my/328/ Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan S. Ahmad, N. Muhammad, A. Muchtar, J. Sahari,, K.R Jamaludin, M.H.I. Ibrahim, N. H. Mohamad Nor, Murtadhahadi, The mechanical and physical propertics of titanium foam sintered at different temperatures are reported in this paper. In this work, the slurry method has been used for the production of titanium foams using pure titanium and titanium alloy (Ti6Al4V). The titanium slurry was first prepared by mixing the titanium powder, polyethylene glycol (PEG), methylcellulose and water. Polyurethane (PU) foams, which acted as scaffolds were then impregnated in the slurry, followed by drying at room temperature. These were later sintered in a high temperature vacuum furnace at 1200oC, 1250oC and 1300°C. The resultant titanium foams were characterised using Scanning Electron Microscopy (SEM) and the compressive strength test. The range of pore sizes obtained was between 388 μm to 1.07 mm, with a strut size in the range of 59.4 μm to 227 μm. The highest compressive strength obtained was 14.85 MPa. This was for the titanium alloy foam which had been sintered at 1250°C. The highest density (1.25 g/cm3) obtained was for the pure titanium foams that were sintered at 1300°C. For these, the porosity was found to be 65.05%. In general however, the most suitable sintering temperature was found to be 1250°C for both the pure titanium and titanium alloy. Universiti Kebangsaan Malaysia 2010-02 Article PeerReviewed application/pdf en http://journalarticle.ukm.my/328/1/ S. Ahmad, N. Muhammad, and A. Muchtar, and J. Sahari,, and K.R Jamaludin, and M.H.I. Ibrahim, and N. H. Mohamad Nor, and Murtadhahadi, (2010) Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan. Sains Malaysiana, 39 (1). pp. 77-82. ISSN 0126-6039 http://www.ukm.my/~jsm/contents.html
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Kebangasaan Malaysia
building	UKM Institutional Repository
collection	Online Access
language	English
description	The mechanical and physical propertics of titanium foam sintered at different temperatures are reported in this paper. In this work, the slurry method has been used for the production of titanium foams using pure titanium and titanium alloy (Ti6Al4V). The titanium slurry was first prepared by mixing the titanium powder, polyethylene glycol (PEG), methylcellulose and water. Polyurethane (PU) foams, which acted as scaffolds were then impregnated in the slurry, followed by drying at room temperature. These were later sintered in a high temperature vacuum furnace at 1200oC, 1250oC and 1300°C. The resultant titanium foams were characterised using Scanning Electron Microscopy (SEM) and the compressive strength test. The range of pore sizes obtained was between 388 μm to 1.07 mm, with a strut size in the range of 59.4 μm to 227 μm. The highest compressive strength obtained was 14.85 MPa. This was for the titanium alloy foam which had been sintered at 1250°C. The highest density (1.25 g/cm3) obtained was for the pure titanium foams that were sintered at 1300°C. For these, the porosity was found to be 65.05%. In general however, the most suitable sintering temperature was found to be 1250°C for both the pure titanium and titanium alloy.
format	Article
author	S. Ahmad, N. Muhammad, A. Muchtar, J. Sahari,, K.R Jamaludin, M.H.I. Ibrahim, N. H. Mohamad Nor, Murtadhahadi,
spellingShingle	S. Ahmad, N. Muhammad, A. Muchtar, J. Sahari,, K.R Jamaludin, M.H.I. Ibrahim, N. H. Mohamad Nor, Murtadhahadi, Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
author_facet	S. Ahmad, N. Muhammad, A. Muchtar, J. Sahari,, K.R Jamaludin, M.H.I. Ibrahim, N. H. Mohamad Nor, Murtadhahadi,
author_sort	S. Ahmad, N. Muhammad,
title	Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
title_short	Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
title_full	Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
title_fullStr	Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
title_full_unstemmed	Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
title_sort	pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan
publisher	Universiti Kebangsaan Malaysia
publishDate	2010
url	http://journalarticle.ukm.my/328/ http://journalarticle.ukm.my/328/ http://journalarticle.ukm.my/328/1/
first_indexed	2023-09-18T19:30:36Z
last_indexed	2023-09-18T19:30:36Z
_version_	1777404935608991744

Pencirian titanium berbusa yang dihasilkan pada suhu pensinteran yang berbeza menggunakan kaedah buburan

Similar Items