Study of machining parameters of surface roughness in electro discharge machining of tool steel

This thesis presents the study of machining parameters on surface roughness in Electro Discharge Machining (EDM) of tool steel. The operation of EDM is based on removing material from the workpiece by a series of repeated electrical discharges, produced by electric pulse generators at short interval...

Full description

Bibliographic Details
Main Author:	Zairul Ezree , Mohd Yunus
Format:	Undergraduates Project Papers
Language:	English
Published:	2008
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://umpir.ump.edu.my/id/eprint/221/ http://umpir.ump.edu.my/id/eprint/221/1/Zairul_Ezree_Mohd_Yunus.pdf

id	ump-221
recordtype	eprints
spelling	ump-2212015-03-03T06:15:52Z http://umpir.ump.edu.my/id/eprint/221/ Study of machining parameters of surface roughness in electro discharge machining of tool steel Zairul Ezree , Mohd Yunus TA Engineering (General). Civil engineering (General) This thesis presents the study of machining parameters on surface roughness in Electro Discharge Machining (EDM) of tool steel. The operation of EDM is based on removing material from the workpiece by a series of repeated electrical discharges, produced by electric pulse generators at short interval, between an electrode and workpiece that being machine in dielectric fluid medium. The Full Factorial Design of Experiment (DOE) from software STATISTICA was used to formulate the experiment layout, to analyze the effect of each parameter on the machining characteristic, and to predict the optimal choices for each EDM parameters. The selected EDM parameters were Peak Current, IP (8 and 16 A), Pulse ON-time (2 and 24 µs), Pulse OFF-time (2 and 3 µs) and Servo Voltage, SV (30 and 40 V). Machining is performed on EDM Sodick AQ55L model. The Surface Roughness Tester Series Mahrsurf XR 20 is used to measure Ra. From the analysis by Full Factorial DOE, it shows that Peak Current and Pulse ON-time have significant effect to surface roughness. The analysis also determined the optimum condition of the machining parameter. The lower values of these parameters the lower surface roughness. The confirmation tests and comparison test were performed for the optimum condition for the machining characteristic. The result of comparison tests showed that the percentage of performed is not accurate but this result can be accepted because the error percentage is below 10%. 2008-11 Undergraduates Project Papers NonPeerReviewed application/pdf en http://umpir.ump.edu.my/id/eprint/221/1/Zairul_Ezree_Mohd_Yunus.pdf Zairul Ezree , Mohd Yunus (2008) Study of machining parameters of surface roughness in electro discharge machining of tool steel. Faculty of Mechanical Engineering, Universiti Malaysia Pahang.
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Malaysia Pahang
building	UMP Institutional Repository
collection	Online Access
language	English
topic	TA Engineering (General). Civil engineering (General)
spellingShingle	TA Engineering (General). Civil engineering (General) Zairul Ezree , Mohd Yunus Study of machining parameters of surface roughness in electro discharge machining of tool steel
description	This thesis presents the study of machining parameters on surface roughness in Electro Discharge Machining (EDM) of tool steel. The operation of EDM is based on removing material from the workpiece by a series of repeated electrical discharges, produced by electric pulse generators at short interval, between an electrode and workpiece that being machine in dielectric fluid medium. The Full Factorial Design of Experiment (DOE) from software STATISTICA was used to formulate the experiment layout, to analyze the effect of each parameter on the machining characteristic, and to predict the optimal choices for each EDM parameters. The selected EDM parameters were Peak Current, IP (8 and 16 A), Pulse ON-time (2 and 24 µs), Pulse OFF-time (2 and 3 µs) and Servo Voltage, SV (30 and 40 V). Machining is performed on EDM Sodick AQ55L model. The Surface Roughness Tester Series Mahrsurf XR 20 is used to measure Ra. From the analysis by Full Factorial DOE, it shows that Peak Current and Pulse ON-time have significant effect to surface roughness. The analysis also determined the optimum condition of the machining parameter. The lower values of these parameters the lower surface roughness. The confirmation tests and comparison test were performed for the optimum condition for the machining characteristic. The result of comparison tests showed that the percentage of performed is not accurate but this result can be accepted because the error percentage is below 10%.
format	Undergraduates Project Papers
author	Zairul Ezree , Mohd Yunus
author_facet	Zairul Ezree , Mohd Yunus
author_sort	Zairul Ezree , Mohd Yunus
title	Study of machining parameters of surface roughness in electro discharge machining of tool steel
title_short	Study of machining parameters of surface roughness in electro discharge machining of tool steel
title_full	Study of machining parameters of surface roughness in electro discharge machining of tool steel
title_fullStr	Study of machining parameters of surface roughness in electro discharge machining of tool steel
title_full_unstemmed	Study of machining parameters of surface roughness in electro discharge machining of tool steel
title_sort	study of machining parameters of surface roughness in electro discharge machining of tool steel
publishDate	2008
url	http://umpir.ump.edu.my/id/eprint/221/ http://umpir.ump.edu.my/id/eprint/221/1/Zairul_Ezree_Mohd_Yunus.pdf
first_indexed	2023-09-18T21:52:11Z
last_indexed	2023-09-18T21:52:11Z
_version_	1777413842326781952

Study of machining parameters of surface roughness in electro discharge machining of tool steel

Similar Items