Performance evaluation of wire electrical discharge machining on Titanium Alloy
The experimental carried out to aim at the selection of the best condition machining parameter combination for wire electrical discharge machining (WEDM) of titanium alloy (Ti–6Al–4V). By using Design Expert 10 software, a series of experiments were performed by selecting pulse-on time, pulse-off t...
| Main Authors: | , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Universiti Malaysia Pahang
2018
|
| Subjects: | |
| Online Access: | http://umpir.ump.edu.my/id/eprint/22125/ http://umpir.ump.edu.my/id/eprint/22125/ http://umpir.ump.edu.my/id/eprint/22125/ http://umpir.ump.edu.my/id/eprint/22125/1/JMMST%201%20-%20027-038.pdf |
| id |
ump-22125 |
|---|---|
| recordtype |
eprints |
| spelling |
ump-221252018-11-12T01:44:46Z http://umpir.ump.edu.my/id/eprint/22125/ Performance evaluation of wire electrical discharge machining on Titanium Alloy Tan, Jun Qi Mohd Yazid, Abu TS Manufactures The experimental carried out to aim at the selection of the best condition machining parameter combination for wire electrical discharge machining (WEDM) of titanium alloy (Ti–6Al–4V). By using Design Expert 10 software, a series of experiments were performed by selecting pulse-on time, pulse-off time, servo voltage and peak current as parameters. The responses that considered were cutting speed, material removal rate, sparking gap and surface roughness. Based on ANOVA analysis, the effect from the parameters on the responses was determined. The optimum machining parameters setting for the maximum cutting speed, minimum sparking gap and minimum surface roughness were found by proceed optimization experiment. Then, each optimization response had their own combination setting on WEDM to cut titanium alloy. 3D response surface graph such as dome and bowl shape represent maximum and minimum point for the solutions had shown in the report. Finally, predicted and actual value from the experiment have been calculated for validation. Universiti Malaysia Pahang 2018-09-13 Article PeerReviewed pdf en http://umpir.ump.edu.my/id/eprint/22125/1/JMMST%201%20-%20027-038.pdf Tan, Jun Qi and Mohd Yazid, Abu (2018) Performance evaluation of wire electrical discharge machining on Titanium Alloy. Journal of Modern Manufacturing Systems and Technology, 1. pp. 27-38. ISSN 2636-9575 http://journal.ump.edu.my/jmmst/article/view/174 DOI: https://doi.org/10.15282/jmmst.v1i1.174 |
| repository_type |
Digital Repository |
| institution_category |
Local University |
| institution |
Universiti Malaysia Pahang |
| building |
UMP Institutional Repository |
| collection |
Online Access |
| language |
English |
| topic |
TS Manufactures |
| spellingShingle |
TS Manufactures Tan, Jun Qi Mohd Yazid, Abu Performance evaluation of wire electrical discharge machining on Titanium Alloy |
| description |
The experimental carried out to aim at the selection of the best condition machining parameter combination for wire electrical discharge machining (WEDM) of titanium alloy
(Ti–6Al–4V). By using Design Expert 10 software, a series of experiments were performed by selecting pulse-on time, pulse-off time, servo voltage and peak current as parameters.
The responses that considered were cutting speed, material removal rate, sparking gap and surface roughness. Based on ANOVA analysis, the effect from the parameters on the
responses was determined. The optimum machining parameters setting for the maximum cutting speed, minimum sparking gap and minimum surface roughness were found by
proceed optimization experiment. Then, each optimization response had their own combination setting on WEDM to cut titanium alloy. 3D response surface graph such as dome and bowl shape represent maximum and minimum point for the solutions had shown in the report. Finally, predicted and actual value from the experiment have been calculated for validation. |
| format |
Article |
| author |
Tan, Jun Qi Mohd Yazid, Abu |
| author_facet |
Tan, Jun Qi Mohd Yazid, Abu |
| author_sort |
Tan, Jun Qi |
| title |
Performance evaluation of wire electrical discharge machining on Titanium Alloy |
| title_short |
Performance evaluation of wire electrical discharge machining on Titanium Alloy |
| title_full |
Performance evaluation of wire electrical discharge machining on Titanium Alloy |
| title_fullStr |
Performance evaluation of wire electrical discharge machining on Titanium Alloy |
| title_full_unstemmed |
Performance evaluation of wire electrical discharge machining on Titanium Alloy |
| title_sort |
performance evaluation of wire electrical discharge machining on titanium alloy |
| publisher |
Universiti Malaysia Pahang |
| publishDate |
2018 |
| url |
http://umpir.ump.edu.my/id/eprint/22125/ http://umpir.ump.edu.my/id/eprint/22125/ http://umpir.ump.edu.my/id/eprint/22125/ http://umpir.ump.edu.my/id/eprint/22125/1/JMMST%201%20-%20027-038.pdf |
| first_indexed |
2023-09-18T22:32:46Z |
| last_indexed |
2023-09-18T22:32:46Z |
| _version_ |
1777416396009897984 |