Microcontroller base full bridge forward power supply unit

Nowadays, there are many power supply unit topologies. In this project, it is been proposed to do the full-bridge dc-dc converter topology. The full-bridge c dc-dc converter topology was chosen for several reasons. The primary benefit of using a Full-Bridge dc-dc converter is its power handling capa...

Full description

Bibliographic Details
Main Author:	Muhamad Azizan, Mat Sirat
Format:	Undergraduates Project Papers
Language:	English
Published:	2008
Subjects:	TK Electrical engineering. Electronics Nuclear engineering
Online Access:	http://umpir.ump.edu.my/id/eprint/414/ http://umpir.ump.edu.my/id/eprint/414/ http://umpir.ump.edu.my/id/eprint/414/1/Muhamad_Azizan_Bin_Mat_Sirat_3189.pdf

id	ump-414
recordtype	eprints
spelling	ump-4142015-03-03T06:03:13Z http://umpir.ump.edu.my/id/eprint/414/ Microcontroller base full bridge forward power supply unit Muhamad Azizan, Mat Sirat TK Electrical engineering. Electronics Nuclear engineering Nowadays, there are many power supply unit topologies. In this project, it is been proposed to do the full-bridge dc-dc converter topology. The full-bridge c dc-dc converter topology was chosen for several reasons. The primary benefit of using a Full-Bridge dc-dc converter is its power handling capabilities, stability, and symmetry. Secondly, using a high frequency transformer is one of the most efficient ways to step up or step down the voltage and to transfer the power to the full-wave rectifier circuit. Basically, this topology is referred to the use of switch mode power supply (SMPS) technique. In designing SMPS, it used high frequency transformer. The purpose of a power transformer in Switch-Mode Power Supplies is to transfer power efficiently and instantaneously from an external electrical source to an external load. In doing so, the transformer also provides important additional capabilities. As mentioned just now, this design uses the high frequency switch. Therefore, a controller is needed to control or vary the duty cycle of PWM during switching time. In this design, PIC is chosen as the main controller of this PSU. PIC was chosen because of ease to program the switching time of four switches. Normally, MOSFET or IGBT is selected for the power switch. Circuit driver is also needed to drive voltage signal from PIC to the power switches. In this case, suitable IC driver must be used. 2008-10 Undergraduates Project Papers NonPeerReviewed application/pdf en http://umpir.ump.edu.my/id/eprint/414/1/Muhamad_Azizan_Bin_Mat_Sirat_3189.pdf Muhamad Azizan, Mat Sirat (2008) Microcontroller base full bridge forward power supply unit. Faculty of Electrical & Electronics Engineering , Universiti Malaysia Pahang . http://iportal.ump.edu.my/lib/item?id=chamo:38411&theme=UMP2
repository_type	Digital Repository
institution_category	Local University
institution	Universiti Malaysia Pahang
building	UMP Institutional Repository
collection	Online Access
language	English
topic	TK Electrical engineering. Electronics Nuclear engineering
spellingShingle	TK Electrical engineering. Electronics Nuclear engineering Muhamad Azizan, Mat Sirat Microcontroller base full bridge forward power supply unit
description	Nowadays, there are many power supply unit topologies. In this project, it is been proposed to do the full-bridge dc-dc converter topology. The full-bridge c dc-dc converter topology was chosen for several reasons. The primary benefit of using a Full-Bridge dc-dc converter is its power handling capabilities, stability, and symmetry. Secondly, using a high frequency transformer is one of the most efficient ways to step up or step down the voltage and to transfer the power to the full-wave rectifier circuit. Basically, this topology is referred to the use of switch mode power supply (SMPS) technique. In designing SMPS, it used high frequency transformer. The purpose of a power transformer in Switch-Mode Power Supplies is to transfer power efficiently and instantaneously from an external electrical source to an external load. In doing so, the transformer also provides important additional capabilities. As mentioned just now, this design uses the high frequency switch. Therefore, a controller is needed to control or vary the duty cycle of PWM during switching time. In this design, PIC is chosen as the main controller of this PSU. PIC was chosen because of ease to program the switching time of four switches. Normally, MOSFET or IGBT is selected for the power switch. Circuit driver is also needed to drive voltage signal from PIC to the power switches. In this case, suitable IC driver must be used.
format	Undergraduates Project Papers
author	Muhamad Azizan, Mat Sirat
author_facet	Muhamad Azizan, Mat Sirat
author_sort	Muhamad Azizan, Mat Sirat
title	Microcontroller base full bridge forward power supply unit
title_short	Microcontroller base full bridge forward power supply unit
title_full	Microcontroller base full bridge forward power supply unit
title_fullStr	Microcontroller base full bridge forward power supply unit
title_full_unstemmed	Microcontroller base full bridge forward power supply unit
title_sort	microcontroller base full bridge forward power supply unit
publishDate	2008
url	http://umpir.ump.edu.my/id/eprint/414/ http://umpir.ump.edu.my/id/eprint/414/ http://umpir.ump.edu.my/id/eprint/414/1/Muhamad_Azizan_Bin_Mat_Sirat_3189.pdf
first_indexed	2023-09-18T21:52:36Z
last_indexed	2023-09-18T21:52:36Z
_version_	1777413868592562176

Microcontroller base full bridge forward power supply unit

Similar Items