A study on tool deflection during deep pocketing cycle

Tool deflection during deep pocketing cycle will cause tapper in mould and die. This problem can cause defect on final product and also increases cost and time wasting in manufacturing process. This study basically shows a detailed study to overcome tapper problem in deep pocket. Dimensional accurac...

Full description

Bibliographic Details
Main Author: Zikrulhakim, Muhd Zahid
Format: Undergraduates Project Papers
Language:English
English
English
Published: 2013
Subjects:
Online Access:http://umpir.ump.edu.my/id/eprint/6560/
http://umpir.ump.edu.my/id/eprint/6560/
http://umpir.ump.edu.my/id/eprint/6560/1/CD7773.pdf
http://umpir.ump.edu.my/id/eprint/6560/4/1.pdf
http://umpir.ump.edu.my/id/eprint/6560/5/3.pdf
id ump-6560
recordtype eprints
spelling ump-65602016-07-14T03:45:54Z http://umpir.ump.edu.my/id/eprint/6560/ A study on tool deflection during deep pocketing cycle Zikrulhakim, Muhd Zahid TA Engineering (General). Civil engineering (General) Tool deflection during deep pocketing cycle will cause tapper in mould and die. This problem can cause defect on final product and also increases cost and time wasting in manufacturing process. This study basically shows a detailed study to overcome tapper problem in deep pocket. Dimensional accuracy due to tapper problem was analyzed in order to obtain optimum cutting parameters. The pocket part was drawn by using CATIA software. The data collected during experiment was analyzed using signal to noise ratio through Minitab software. From the analysis, it was found that depth of cut has gives the most effect on tapper problem, followed by feed rate and spindle speed. From the result, it is shown that level 1 of depth of cut which is 0.3mm, level 1 of feed rate which is 64mm and level 2 of spindle speed which is 1280rpm was the best cutting parameter. Hence, from these cutting parameters, the tapper problem cause by tool deflection during deep pocketing cycle can be overcome. 2013-06 Undergraduates Project Papers NonPeerReviewed application/pdf en http://umpir.ump.edu.my/id/eprint/6560/1/CD7773.pdf application/pdf en http://umpir.ump.edu.my/id/eprint/6560/4/1.pdf application/pdf en http://umpir.ump.edu.my/id/eprint/6560/5/3.pdf Zikrulhakim, Muhd Zahid (2013) A study on tool deflection during deep pocketing cycle. Faculty of Manufacturing Engineering , Universiti Malaysia Pahang. http://iportal.ump.edu.my/lib/item?id=chamo:78137&theme=UMP2
repository_type Digital Repository
institution_category Local University
institution Universiti Malaysia Pahang
building UMP Institutional Repository
collection Online Access
language English
English
English
topic TA Engineering (General). Civil engineering (General)
spellingShingle TA Engineering (General). Civil engineering (General)
Zikrulhakim, Muhd Zahid
A study on tool deflection during deep pocketing cycle
description Tool deflection during deep pocketing cycle will cause tapper in mould and die. This problem can cause defect on final product and also increases cost and time wasting in manufacturing process. This study basically shows a detailed study to overcome tapper problem in deep pocket. Dimensional accuracy due to tapper problem was analyzed in order to obtain optimum cutting parameters. The pocket part was drawn by using CATIA software. The data collected during experiment was analyzed using signal to noise ratio through Minitab software. From the analysis, it was found that depth of cut has gives the most effect on tapper problem, followed by feed rate and spindle speed. From the result, it is shown that level 1 of depth of cut which is 0.3mm, level 1 of feed rate which is 64mm and level 2 of spindle speed which is 1280rpm was the best cutting parameter. Hence, from these cutting parameters, the tapper problem cause by tool deflection during deep pocketing cycle can be overcome.
format Undergraduates Project Papers
author Zikrulhakim, Muhd Zahid
author_facet Zikrulhakim, Muhd Zahid
author_sort Zikrulhakim, Muhd Zahid
title A study on tool deflection during deep pocketing cycle
title_short A study on tool deflection during deep pocketing cycle
title_full A study on tool deflection during deep pocketing cycle
title_fullStr A study on tool deflection during deep pocketing cycle
title_full_unstemmed A study on tool deflection during deep pocketing cycle
title_sort study on tool deflection during deep pocketing cycle
publishDate 2013
url http://umpir.ump.edu.my/id/eprint/6560/
http://umpir.ump.edu.my/id/eprint/6560/
http://umpir.ump.edu.my/id/eprint/6560/1/CD7773.pdf
http://umpir.ump.edu.my/id/eprint/6560/4/1.pdf
http://umpir.ump.edu.my/id/eprint/6560/5/3.pdf
first_indexed 2023-09-18T22:02:26Z
last_indexed 2023-09-18T22:02:26Z
_version_ 1777414487750475776