Showing 1 - 20 results of 40 for search '"Molding (process)"', query time: 0.04s Refine Results
  1. 1
    Modeling and Flow Analysis of Pure Nylon Polymer for Injection Molding Process
    “…) polymer for injection molding process. To determine the best molding conditions, a series of simulations…”
    Get full text
    Get full text
    Get full text
  2. 2
    Investigation on mechanical properties of ABS using rapid rpototyping technology and injection molding process
    “… molding process. The results of the experiment will be fully used to evaluate the advantages…”
    Get full text
    Get full text
  3. 3
    Mold design for plastics injection molding process (two colors) and analysis of gates location
    by Ahmad Zulhelmi, Muhamad
    Published 2009
    “…This thesis describe about the mold design for plastic injection molding process for two colors…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  4. 4
    A review of important considerations in the compression molding process of short natural fiber composites
    “…The study reviewed crucial parameters in the compression molding process for biocomposites…”
    Get full text
    Get full text
    Get full text
    Get full text
  5. 5
    Moldability characteristics of 3 mol% Yttria Stabilized Zirconia feedstock for micro-powder injection molding process
    Get full text
    Get full text
    Get full text
  6. 6
    Optimization parameters to reduce the warpage defect of plastic injection molding process for a thin-shell part using design of experiment
    Get full text
    Get full text
    Get full text
  7. 7
    Simulation of micro-injection molding
    “…Two challenges in micro-injection molding process were the modification of conventional injection…”
    Get full text
    Get full text
  8. 8
    Analysis and prediction of micro injection molding part using moldflow simulation software
    by Mohammad Farhan, Othman
    Published 2012
    “… parts is much higher compare to typical injection molding process. Normally, micro injection molding…”
    Get full text
    Get full text
    Get full text
  9. 9
    Analysis and prediction of injected parts by using mould filling simulation software
    by Nurul Farhanah, Rosli
    Published 2013
    “… problems and defects occur in plastic injection molding process can be determined. Previously…”
    Get full text
    Get full text
    Get full text
  10. 10
    Optimization of the injection molding parameters using the Taguchi method / Shahrul Kamaruddin, Zahid A. Khan and K. S. Wan
    Published 2006
    “…, is used to determine the optimal parameters for an injection molding process. An orthogonal array…”
    Get full text
    Get full text
  11. 11
    Analysis of filling stage for injection molding
    by Muhammad Arshad, Zainol Abidin
    Published 2007
    “…The injection or filling stage is the most important stage in injection molding process cycle…”
    Get full text
    Get full text
    Get full text
  12. 12
    Modeling and properties of glass fibre-reinforced nylon
    by Nurizzathanis, Mohamad Kusaseh
    Published 2015
    “… flow of plastic part modeling for injection molding process by using Autodesk Moldflow Insights…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  13. 13
    Numerical Prediction of Flow Induced Fibers Orientation in Injection Molded Polymer Composites
    “…Since the filling stage of injection molding process has important effect on the determination…”
    Get full text
    Get full text
    Get full text
  14. 14
    Experimental investigation on flexure and impact properties of injection molded polypropylene-nylon 6-glass fiber polymer composites
    “… composites were prepared using injection molding process. Specimens of four different compositions such as 80…”
    Get full text
    Get full text
    Get full text
  15. 15
    Simulation development, design and test of handset casing
    by Noorsakinah, Shafie
    Published 2008
    “…Injection molding process is the predominant method for producing plastic parts. Injection molded…”
    Get full text
    Get full text
    Get full text
  16. 16
    Conceptual design of two-plate injection mould for UMP's keychain
    by Azhar, Yusop
    Published 2008
    “… product can be produced using injection molding process that required good design of mold. In design…”
    Get full text
    Get full text
  17. 17
    Knowledge-based approach for stretch blow molding
    “… problem. The stretch blow molding process, like other manufacturing processes, appears…”
    Get full text
    Get full text
  18. 18
    Micromolding of three-dimensional components
    “… ion beam sputtering to produce a microcavity for subsequent molding process. The simulation pinpointed…”
    Get full text
    Get full text
  19. 19
    Particle size and injection temperature effect on the injection molding of SS316L powder / Khairur Rijal Jamaludin … [et al.]
    Published 2008
    “… that the success of the molding process depends on the feedstock rheological properties. Fine powder particles…”
    Get full text
    Get full text
  20. 20
    Degradation characteristics of SPF/SPS biocomposites
    “… incorporated into sugar palm starch (SPS) plasticised with glycerol using the com¬pression molding process…”
    Get full text
    Get full text
    Get full text
Search Tools: RSS Feed – Email Search