Showing 1 - 16 results of 16 for search '"revolutions per minute"', query time: 0.04s Refine Results
  1. 1
    Esterification of free fatty acids in simulated waste cooking oil using sulphuric acids as catalyst: pre-treatment of feedstock for biodiesel production
    by Amir Lukmanhisyam, Haili
    Published 2014
    “… by manipulating the oil and methanol ratio, varying the stirring speed or revolutions per minute (rpm…”
    Get full text
    Get full text
    Get full text
  2. 2
    Vibration analysis of vehicle engine mounting
    by Teh, Swee Ing
    Published 2013
    “… revolutions per minute (rpm). The experiment is carried out on a stationary vehicle using DasyLab software…”
    Get full text
    Get full text
    Get full text
  3. 3
    Tribological Behaviour Improvement of Lubricant Using Copper (II) Oxide Nanoparticles as Additive
    “… in the analysis using the wear tester (piston ring) were load, revolutions per minute (rpm), and concentration…”
    Get full text
    Get full text
    Get full text
  4. 4
    PID control system implementation in embedded system for DC motor speed control
    by Ariff, Che Mohd Noor
    Published 2008
    “… purpose. The focus is on 12 volt DC motor with 30 revolutions per minute (rpm) maximum speed. No-load case…”
    Get full text
    Get full text
    Get full text
  5. 5
    Engine speed and air-fuel ratio effect on the combustion of methane augmented hydrogen rich syngas in DI SI engine
    “… to 2400 revolutions per minute (rpm) with an interval of 300 rpm. The result indicated that coefficient…”
    Get full text
    Get full text
    Get full text
    Get full text
  6. 6
    Development of once per revolution sensor chatter
    by Edzamila, Dzaidi
    Published 2013
    “… usually displays the revolutions per minute (RPM) on a calibrated analogue dial, but for this project…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  7. 7
    Anti-theft car seat design (electronic/control)
    by Mahfuzah, Mohd Nasir
    Published 2009
    “… at high RPM or revolutions per minute so it is really necessary to reduce the rate at the wheel spins…”
    Get full text
    Get full text
    Get full text
  8. 8
    Sound intensity mapping of two stroke engine by using hemispherical surface coordinate arrangement
    “… at range 800 to 4800 revolution per minute (rpm). A single module of microphone is used to identify sound…”
    Get full text
    Get full text
    Get full text
  9. 9
    Turbulent flame speed in spark ignition engine combustion process using computational fluid dynamics
    by Muhammad Saiful, Mustafa
    Published 2011
    “… process at single operating point for 2000 revolution per minute (rpm) engine speed. Turbulent flame speed…”
    Get full text
    Get full text
    Get full text
  10. 10
    Design, simulation and practical experimentation of miniaturized turbine flow sensor for flow meter assessment
    “… was tested using a DC motor which was programmed to control the revolution per minute(rpm) of the turbine…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  11. 11
    Multi dimensional modelling of a high pressure natural gas fuel injection process in prechamber of a single cylinder four-stroke engine
    by Muhamad Azman, Mohd Yamin
    Published 2012
    “… on the combustion model with different ignition and injection timing. 2000 revolution per minute (rpm) and 500…”
    Get full text
    Get full text
    Get full text
  12. 12
    Grid sensitivity study of in-cylinder engine meshing appropriate for flow and combustion analysis using computational fluid dynamics (CFD)
    by Umar, Shafee
    Published 2009
    “… it is analyzed. The speed of engine is fixed at 2000 revolution per minute (rpm) and the turbulence model is k…”
    Get full text
    Get full text
    Get full text
  13. 13
    Effect of constant and varying mixture properties in spark ignition engine combustion process using computational fluid dynamics
    by Omar, Arshad
    Published 2012
    “… as the base line engine design for the simulation model. 2000 revolution per minute (rpm) and 1000 iterations…”
    Get full text
    Get full text
    Get full text
  14. 14
    Analysis of a spur gear in automative system using finite element software
    by Mohd Khairi, Mohammad
    Published 2013
    “… is if the speed in term revolution per minute is low, so the stress, strain and also displacement value…”
    Get full text
    Get full text
    Get full text
  15. 15
    Effect of nanopolyacrylate and natural rubber latex on asphalt binder and mixture performance / Ekarizan Shaffie
    by Shaffie, Ekarizan
    Published 2018
    “… revolution per minute. While, Nanocomposite (NC) polymer modified asphalt binder was prepared by mixing…”
    Get full text
    Get full text
  16. 16
    Effect of nanopolyacrylate and natural rubber latex on asphalt binder and mixture performance / Ekarizan Shaffie
    by Shaffie, Ekarizan
    Published 2018
    “… revolution per minute. While, Nanocomposite (NC) polymer modified asphalt binder was prepared by mixing…”
    Get full text
    Get full text
Search Tools: RSS Feed – Email Search