Showing 1 - 20 results of 26 for search 'Machine taper', query time: 0.05s Refine Results
  1. 1
    Effects of hole taper on mild steel machining using injection flushing type of electrical discharge machine
    by Sahwal Waty, Marno
    Published 2010
    “…Electric discharge machining (EDM) is a process for shaping hard metals and forming deep…”
    Get full text
    Get full text
    Get full text
  2. 2
    Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
    “… and accuracy are needed, the taper and corner roundness on the workpiece machined need to be controlled…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  3. 3
    Investigation of taper angle in dry micro wire EDM
    “… voltage has major influence on taper angle. The optimum machining parameters for minimum taper angle were…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  4. 4
    Experimental study of kerf width and taper on laser beam cutting acrylic sheet
    by Mohamad Yazid, Idris
    Published 2009
    “…This thesis is mainly about the study and analysis of the kerf width and taper on acrylic sheet…”
    Get full text
    Get full text
    Get full text
  5. 5
    Effect of Taper Pin Ratio on AA7075 Aluminium Alloy Friction Stir Welding
    “… conventional milling machine. The shoulder diameter used in this experiment is fixed at 18mm. The taper pin…”
    Get full text
    Get full text
    Get full text
    Get full text
  6. 6
    Effect of Taper Pin Ratio on Microstructure and Mechanical Property of Friction Stir Welded AZ31 Magnesium Alloy
    “… conventional milling machine. The shoulder diameter used in this experiment is fixed at 18mm. The taper pin…”
    Get full text
    Get full text
    Get full text
  7. 7
    Modular robotic platform for autonomous machining
    “…. Finally, the machined holes’ quality was measured in terms of circularity and taperness. It was observed…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  8. 8
    Application of focused ion beam for machining of nanopillar sheet
    by Ali, Mohammad Yeakub
    Published 2011
    “…, which were acceleration voltage, dwell time and milled depth. The response variables were taper angle (θ…”
    Get full text
    Get full text
    Get full text
  9. 9
    Performance analysis of abrasive waterjet machining process at low pressure
    “…Normally, a commercial waterjet cutting machine can generate water pressure up to 600 MPa…”
    Get full text
    Get full text
    Get full text
    Get full text
  10. 10
    A study on abrasive water jet machining of aluminum with garnet abrasives
    “… abrasive water jet machining of aluminum has been investigated. The type of abrasive used was gamet…”
    Get full text
    Get full text
    Get full text
    Get full text
  11. 11
    Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
    “… and micro electrical discharge machining (EDM). The microholes were produced on beryllium copper alloy…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  12. 12
    Performance of different abrasive materials during abrasive water jet machining of glass
    “…Different types of abrasives are used in abrasive water-jet machining like garnet, aluminum oxide…”
    Get full text
    Get full text
    Get full text
    Get full text
  13. 13
    Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
    “…Abstract This paper presents a study on the effect of abrasive water jet machining (AWJM) process…”
    Get full text
    Get full text
    Get full text
    Get full text
  14. 14
    A study of abrasive water jet machining process on glass/epoxy composite laminate
    by M. A., Amir, Khan, Ahsan Ali
    Published 2009
    “…Surface roughness (Ra) and kerf taper ratio (TR) characteristics of an abrasive water jet machined…”
    Get full text
    Get full text
    Get full text
    Get full text
  15. 15
    Sugeno-Fuzzy Expert System Modeling for Quality Prediction of Non-Contact Machining Process
    “… modelling method to investigate the taper quality of laser lathing, which seeks to replace traditional lathe…”
    Get full text
    Get full text
    Get full text
  16. 16
    Influence of Machine Variables and Tool Profile on the Tensile Strength of Dissimilar AA7075-AA6061 Friction Stir Welds
    “… mainly depends on machine variables and tool design. In this paper, FSW of dissimilar AA7075-AA6061…”
    Get full text
    Get full text
    Get full text
    Get full text
    Get full text
  17. 17
    A new experimental approach to determination of critical depth in high speed machining of soda-lime glass
    “… transition depth, machining was performed on a tapered surface. Vibration signals from an accelerometer…”
    Get full text
    Get full text
    Get full text
  18. 18
    Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish
    “… keV Ga+ FIB was used to machine the nanopillars. A reversed bitmap method was used to fabricate…”
    Get full text
    Get full text
  19. 19
    Fabrication of silicon nanopillar sheet for Cell Culture Dish
    “… keV Ga+ FIB was used to machine the nanopillars. A reversed bitmap method was used to fabricate…”
    Get full text
    Get full text
    Get full text
    Get full text
  20. 20
    Development and performance evaluation of modular RC-based power supply for micro-EDM
    “… Electrical Discharge Machining. A low discharge energy per pulse is important to achieve micro-level…”
    Get full text
    Get full text
    Get full text
    Get full text
Search Tools: RSS Feed – Email Search