Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions

by Nurul Amin, A. K. M, Mokhtar, Suhaily, D. Arif, Muammer
Published 2012

Machinability aspects in heat assisted machining of hardened steel AISI H13 using coated carbide tool

by Amin, A. K. M. Nurul, Mokhtar, Suhaily, Ab. Razak, Nur Hayati
Published 2011

Study on machinability effect of surface roughness in milling kenaf fiber reinforced plastic composite (unidirectional) using response surface methodology

by Harun, Azmi, Che Haron, Che Hassan, A.Ghani, Jaharah, Mokhtar, Suhaily
Published 2016

Evaluation of thrust force in drilling of woven kenaf fiber reinforced epoxy composite laminates

by Mokhtar, Suhaily, Che Haron, Che Hassan, A. Ghani, Jaharah, Harun, Azmi
Published 2017

Comparison effect of delamination factor (Fd) on unidirectional and woven kenaf fibre reinforced plastic composite materials during milling process [Pembandingan kesan faktor pelek...

by Azmi, H., Che Haron, Che Hassan, A. Ghani, Jaharah, Mokhtar, Suhaily
Published 2018

Machinability improvement by workpiece preheating during end milling AISI H13 hardened steel

by Mokhtar, Suhaily, Amin, A. K. M. Nurul, Patwari, Md Anayet Ullah, Abdul Razak, Nurhayati
Published 2011

A new technique to improve the machinability of hardened steel AISI H13 in end milling

by Amin, A. K. M. Nurul, Mokhtar, Suhaily, Patwari, Muhammed Anayet Ullah, Abdul Razak, Nurhayati
Published 2010

Machinability study on milling kenaf fiber reinforced plastic composite materials using the design of experiments

by Harun, Azmi, Che Haron, Che Hassan, A. Ghani, Jaharah, Mokhtar, Suhaily, Abdul Rahim, Yuzairi
Published 2018

Comparison of machinability of ceramic insert in room temperature and cryogenic cooling conditions during end milling inconel 718

by Amin, A. K. M. Nurul, Mokhtar, Suhaily, Patwari, Muhammed Anayet Ullah, Hazim, A., Adlan, Z.
Published 2011

The optimization study on the tool wear of carbide cutting tool during milling Carbon Fibre Reinforced (CFRP) using Response Surface Methodology (RSM)

by Muhamad Khairussaleh, Nor Khairusshima, Zakwan, Muhammad Hafiz, Mokhtar, Suhaily, Shaffiar, Norhashimah, Syed Shaharuddin, Sharifah Imihezri
Published 2018

Analysis and modeling of delamination factor in drilling of woven kenaf fiber reinforced epoxy using Box Behnken experimental design

by Mokhtar, Suhaily, Che Haron, Che Hassan, A. Ghani, Jaharah, Mohd Ali, Afifah, Mohd Khairussaleh, Nor Khairusshima
Published 2018

Enhancement of machinability of nickel based alloy - inconel 718 by induction preheating in end milling using ceramic inserts

by Mokhtar, Suhaily, Amin, A. K. M. Nurul, Patwari, Anayet Ullah, A. Azhar, A. Hazim, A. R., Zulkhari
Published 2010

Study on drilling induced delamination of woven kenaf fiber reinforced epoxy composite using carbide drills

by Mokhtar, Suhaily, Che Haron, Che Hassan, A. Ghani, Jaharah, Harun, Azmi, Mohd Ali, Afifah, Muhamad Khairussaleh, Nor Khairusshima
Published 2018

The relationship of cutting chip type, length and thickness to wear of Zirconia Toughened Alumina Added with Magnesium Oxide (ZTA-MgO) cutting tool

by Mohd Ali, Afifah, Janal, Nurul Nabihah, Hamidon, Nor Ezzati, Ahmad Azhar, Ahmad Zahirani, Mokhtar, Suhaily, Bahar, Rubina, Ahmad, Zainal Arifin
Published 2018

The effect of cutting parameters on the performance of ZTA-MgO cutting tool

by Mohd Ali, Afifah, Hamidon, N. E., Zaki, N. K.M., Mokhtar, Suhaily, Ahmad Azhar, Ahmad Zahirani, Bahar, Rubina., Ahmad, Zainal Arifin Azhar
Published 2018