The effect of cutting parameters on the performance of ZTA-MgO cutting tool

The effect of cutting parameters on the performances of ZTA-MgO ceramic cutting tool investigated. The aim of this project is to discover the effect of cutting speed and feedrate on the performance of the ZTA-MgO cutting tool via wear and surface roughness measurement. CNC turning machining performe...

Full description

Bibliographic Details
Main Authors:	Mohd Ali, Afifah, Hamidon, N. E., Zaki, N. K.M., Mokhtar, Suhaily, Ahmad Azhar, Ahmad Zahirani, Bahar, Rubina., Ahmad, Zainal Arifin Azhar
Format:	Conference or Workshop Item
Language:	English English
Published:	Institute of Physics Publishing 2018
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/65136/ http://irep.iium.edu.my/65136/ http://irep.iium.edu.my/65136/ http://irep.iium.edu.my/65136/1/Ali_2018_IOP_Conf._Ser.%253A_Mater._Sci._Eng._290_012072.pdf http://irep.iium.edu.my/65136/7/65136_The%20effect%20of%20cutting%20parameters%20on%20the%20performance_scopus.pdf

id	iium-65136
recordtype	eprints
spelling	iium-651362018-07-31T09:03:15Z http://irep.iium.edu.my/65136/ The effect of cutting parameters on the performance of ZTA-MgO cutting tool Mohd Ali, Afifah Hamidon, N. E. Zaki, N. K.M. Mokhtar, Suhaily Ahmad Azhar, Ahmad Zahirani Bahar, Rubina. Ahmad, Zainal Arifin Azhar TJ Mechanical engineering and machinery The effect of cutting parameters on the performances of ZTA-MgO ceramic cutting tool investigated. The aim of this project is to discover the effect of cutting speed and feedrate on the performance of the ZTA-MgO cutting tool via wear and surface roughness measurement. CNC turning machining performed using the cutting speed, Vc range from 354 to 471 m/min and the feed rate, f 0.1, 0.3 and 0.5 mm/rev while the depth of cut, d is kept constant at 0.2 mm. The flank wear, crater wear, and chipping were measured accordingly using optical microscope, Matlab programming and SEM. Surface roughness of machined stainless steel 316L surface were measured using the surface roughness tester (Mitutoyo MTR097-8. The result showing the increment trend of flank wear with increment of cutting speed and feed rate with the lowest value of flank wear, 0.061 mm achieved at Vc = 354 m/min and f = 0.1 mm/rev while the highest flank wear is 0.480 mm at Vc = 471 m/min and f = 0.5 mm/rev. The increasing pattern also observed in the crater wear results. The lowest area of crater wear is 2.2736 mm2 at Vc = 354 m/min and f = 0.1 mm/rev while the highest value is 4.8524 mm2 at Vc = 471 m/min and f = 0.5 mm/rev. As for the surface roughness, the higher the cutting speed, the lower the average roughness (Ra) value. Cutting speed, Vc = 471 m/min with f = 0.1 mm/rev has the lowest value of Ra which is 0.72µm. Institute of Physics Publishing 2018-01-01 Conference or Workshop Item PeerReviewed application/pdf en http://irep.iium.edu.my/65136/1/Ali_2018_IOP_Conf._Ser.%253A_Mater._Sci._Eng._290_012072.pdf application/pdf en http://irep.iium.edu.my/65136/7/65136_The%20effect%20of%20cutting%20parameters%20on%20the%20performance_scopus.pdf Mohd Ali, Afifah and Hamidon, N. E. and Zaki, N. K.M. and Mokhtar, Suhaily and Ahmad Azhar, Ahmad Zahirani and Bahar, Rubina. and Ahmad, Zainal Arifin Azhar (2018) The effect of cutting parameters on the performance of ZTA-MgO cutting tool. In: International Conference on Advances in Manufacturing and Materials Engineering 2017, ICAMME 2017, 8- 9 August 2017, International Islamic University Malaysia (IIUM), Gombak Campus, Kuala Lumpur. http://iopscience.iop.org/article/10.1088/1757-899X/290/1/012072/meta 10.1088/1757-899X/290/1/012072
repository_type	Digital Repository
institution_category	Local University
institution	International Islamic University Malaysia
building	IIUM Repository
collection	Online Access
language	English English
topic	TJ Mechanical engineering and machinery
spellingShingle	TJ Mechanical engineering and machinery Mohd Ali, Afifah Hamidon, N. E. Zaki, N. K.M. Mokhtar, Suhaily Ahmad Azhar, Ahmad Zahirani Bahar, Rubina. Ahmad, Zainal Arifin Azhar The effect of cutting parameters on the performance of ZTA-MgO cutting tool
description	The effect of cutting parameters on the performances of ZTA-MgO ceramic cutting tool investigated. The aim of this project is to discover the effect of cutting speed and feedrate on the performance of the ZTA-MgO cutting tool via wear and surface roughness measurement. CNC turning machining performed using the cutting speed, Vc range from 354 to 471 m/min and the feed rate, f 0.1, 0.3 and 0.5 mm/rev while the depth of cut, d is kept constant at 0.2 mm. The flank wear, crater wear, and chipping were measured accordingly using optical microscope, Matlab programming and SEM. Surface roughness of machined stainless steel 316L surface were measured using the surface roughness tester (Mitutoyo MTR097-8. The result showing the increment trend of flank wear with increment of cutting speed and feed rate with the lowest value of flank wear, 0.061 mm achieved at Vc = 354 m/min and f = 0.1 mm/rev while the highest flank wear is 0.480 mm at Vc = 471 m/min and f = 0.5 mm/rev. The increasing pattern also observed in the crater wear results. The lowest area of crater wear is 2.2736 mm2 at Vc = 354 m/min and f = 0.1 mm/rev while the highest value is 4.8524 mm2 at Vc = 471 m/min and f = 0.5 mm/rev. As for the surface roughness, the higher the cutting speed, the lower the average roughness (Ra) value. Cutting speed, Vc = 471 m/min with f = 0.1 mm/rev has the lowest value of Ra which is 0.72µm.
format	Conference or Workshop Item
author	Mohd Ali, Afifah Hamidon, N. E. Zaki, N. K.M. Mokhtar, Suhaily Ahmad Azhar, Ahmad Zahirani Bahar, Rubina. Ahmad, Zainal Arifin Azhar
author_facet	Mohd Ali, Afifah Hamidon, N. E. Zaki, N. K.M. Mokhtar, Suhaily Ahmad Azhar, Ahmad Zahirani Bahar, Rubina. Ahmad, Zainal Arifin Azhar
author_sort	Mohd Ali, Afifah
title	The effect of cutting parameters on the performance of ZTA-MgO cutting tool
title_short	The effect of cutting parameters on the performance of ZTA-MgO cutting tool
title_full	The effect of cutting parameters on the performance of ZTA-MgO cutting tool
title_fullStr	The effect of cutting parameters on the performance of ZTA-MgO cutting tool
title_full_unstemmed	The effect of cutting parameters on the performance of ZTA-MgO cutting tool
title_sort	effect of cutting parameters on the performance of zta-mgo cutting tool
publisher	Institute of Physics Publishing
publishDate	2018
url	http://irep.iium.edu.my/65136/ http://irep.iium.edu.my/65136/ http://irep.iium.edu.my/65136/ http://irep.iium.edu.my/65136/1/Ali_2018_IOP_Conf._Ser.%253A_Mater._Sci._Eng._290_012072.pdf http://irep.iium.edu.my/65136/7/65136_The%20effect%20of%20cutting%20parameters%20on%20the%20performance_scopus.pdf
first_indexed	2023-09-18T21:32:25Z
last_indexed	2023-09-18T21:32:25Z
_version_	1777412598752346112

The effect of cutting parameters on the performance of ZTA-MgO cutting tool

Similar Items